Repository logo
 

Faculty of Engineering and Built Environment

Permanent URI for this communityhttp://ir-dev.dut.ac.za/handle/10321/9

Browse

Start date: 2020Subject: search.filters.subject.Photovoltaic power generation

Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    Design and application of passive filters for improved power quality in standalone PV system
    (2024-05) Dlamini, Sandile; Adebiyi, Abayomi Aduragba; Kabeya, Musasa
    Harmonic components have developed in power systems due to the non-linear properties of the circuit components utilized in power electronics-based products and their rapid application. Power systems rely on fundamental quantities like sinusoidally varying voltage and current, which oscillate at a frequency of 50 Hz. The standard restrictions of IEEE-519-1992 were utilized as a benchmark in this study. To generate the best output, the total harmonic distortion (THD) should be decreased below the limit, even for certain individual harmonic numbers, and reflect the power factor output. Using the results of the simulation and projections for each mitigation strategy, the THDI can be reduced below the IEEE-519 standard whilst also providing cost and electrical advantages. Analysed and modelled is the PV system, which comprises solar panels, a DC-DC converter, a DC-AC inverter, and a non-linear load. Passive filters are an effective solution for improving power quality in standalone photovoltaic (PV) systems. This dissertation provides an overview of the design and application of passive filters for this purpose. Firstly, an introduction to PV systems and the power quality issues associated with them was preferred. Next, different types of passive filters, namely LC filters, LCL filters and LLCL filters, are discussed along with their advantages and disadvantages, and the design considerations for these filters, including the selection of filter components and the calculation of filter parameters. The application of passive filters in standalone PV systems was then discussed, including their implementation in DC-DC converters and Z-Source inverters and, the design of PWM controllers such as the constant boost control method and simple boost control method. The analysis of the outcome of the engineered systems was conducted according to the IEEE standard and SANS 10142 Standard to protect the connected equipment within the off-grid network. The outcomes pertain to the single-phase stand-alone/off-grid photovoltaic system and the single-phase Z-Source inverter. The Z-Source inverter is equipped with two distinct methods for PWM control, namely the constant boost control method and the simple boost control method. All three designs incorporate three passive filters, namely the LC filter, the LCL filter and the LLCL filter. The results were obtained from the network consisting of three distinct designs. LLCL demonstrates superior performance as a passive filter, substantiating its position as the optimal choice. The optimal outcomes of a single-phase off-photovoltaic (PV) network can be achieved using LC, LCL and LLCL filters, with corresponding percentages of 2.99%, 2.45% and 1.71% respectively. Unfiltered was 89.05%, which is not good for the equipment connected to the network. The Z-Source showcases the capability of voltage amplification to an infinite level, rendering it highly effective in minimizing total harmonic distortion. This research investigation further demonstrated the efficacy of the Z-Source Inverter with Constant Control Boost Method and Simple Boost Control Method, achieving unfiltered total harmonic distortion levels of 38.85% and 44.96% respectively. The Z-Source inverter, when combined with the Constant Boost Control method and Simple Boost Control method, exhibits various filter configurations such as LC, LCL, and LLCL filters. In the context of the constant boost control and simple boost control methods, it is imperative to assess the total harmonic distortion percentage of voltage and current for LC, LCL, and LLCL configurations. The constant boost control voltage (LC, LCL, LLCL) and current total harmonic distortion (LC, LCL, LLCL) are measured at 4.177%, 2.655%, 1.951%, and 2.958%, 2.09%,1.465% correspondingly. The voltage-based boost control methods, namely LC, LCL and LLCL, exhibit total harmonic distortion levels of 2.345%, 1.920% and 0.211%, respectively. Similarly, the current-based boost control methods, LC, LCL and LLCL, demonstrate total harmonic distortion levels of 2.346%, 1.921%, 0.211%, and 2.346%, 1.921%, 0.211%, respectively. Finally, the dissertation wrapped up by exploring the potential of passive filters for enhancing power quality in standalone PV systems. The thesis offers a comprehensive investigation of the design and implementation of passive filters in standalone PV systems, providing valuable insights for engineers and researchers in the field. It enhances understanding and utilization of these imperative devices.
  • Thumbnail Image
    Item
    Development of an Intelligent Standalone Solar Photovoltaic 48V DC microgrid system
    (2024-05) Makhanya, Thandeka; Pillay, N; Sewsunker, R
    With load shedding negatively affecting South Africans there are many concerns regarding stable power delivery to residential households. Amid all the power delivery concerns some rural communities are still not connected to the existing power infrastructure. Implementation of newer efficient clean energy sources is in demand. A standalone Photovoltaic (PV) Solar distributed renewable energy Direct Current (DC) microgrid can be the best possible approach to tackle the power grid shortcomings and to electrify communities that are not yet covered by the power grid or communities that want to transition to clean energy. The research focuses on the design of an optimal 48 VDC Multiple-PV Standalone microgrid in remote areas not covered by the main grid. The proposed microgrid can be typically used for lighting, charging phones, and other low-power applications. The microgrid will consist of 4 microgrid subgrids, each consisting of a dedicated Solar PV array, battery storage systems, loads, and other components that connect to the DC Bus and need to be monitored and controlled for efficient operation. Furthermore, the subgrids were designed based on the meteorological data of the selected location and the load demand for each subgrid. The microgrid design enables the subgrids to share power through a bidirectional DC-DC converter based on certain conditions. A power-sharing management system was implemented to manage power-sharing ensuring that the sharing subgrid does not drive its users to load shedding. Moreover, the microgrid design was simulated on Matlab/Simulink to observe the operation of the designed system and to determine if the proposed design would be able to achieve the desired goal. The results obtained from simulations indicate that the proposed microgrid design can provide an optimal service to its users by allowing the subgrid with surplus energy to share its power with the subgrid when needed.
  • Thumbnail Image
    Item
    Distribution network performance analysis with high penetration o RTPV and Bess
    (2020-11) Reddy, Rodney; Davidson, Innocent Ewaen; Chetty, Dayahalan
    The consequential effect of meeting electrical demands continues to burden the South African electrical infrastructure. Electrical violations tend to constrain a power system’s ability to supply suitable energy whilst meeting growth demands. Often optimization techniques are utilized to reduce violations, however; constrained networks in dense and radial distribution systems don’t have any quick or short-term solutions. This thesis explores solar rooftop photovoltaics (RTPV) and battery energy storage systems (BESS) as a distributed energy resource to alleviate violations which are currently constraining medium voltage (MV) networks. This research has studied the influential effect of hybrid RTPV systems, with and without BESS. The analysis, simulated with actual all-day load profiles, has uniquely considered RTPV installations for every residential customer connected to an MV network. For the identification of networks that experience violations; informative analysis-results from over eight hundred MV feeders have been studied. These results have been utilized to develop a methodological approach for a technical priority ranking system. This system helps to categorize the severity of network constraints for distribution networks. By modelling a case study, this thesis demonstrates what impact RTPV will have on a technically violated/constrained MV network. This thesis offers an alternative network optimization solution by using RTPV and BESS to address constrained/violated networks. This can assist Utilities to meet electrical demands while complying with statutory regulation limits.