Faculty of Applied Sciences
Permanent URI for this communityhttp://ir-dev.dut.ac.za/handle/10321/5
Browse
14 results
Search Results
Item Development and microbial community analysis of a biological treatment process for edible oil effluent(2003) Bux, Faizal; Tivchev, G. N.Globally, wastewaters emanating from edible oil manufacturers contain high organic (BOD & COD) and phosphate loads and known for creating shock-loading problems for the receiving wastewater treatment installations. Discharge of poor quality final effluents also negatively impact on and cause eutrophication of natural water sources such as rivers and dams. In South Africa, a large concentration ofthe edible industries are localized in the Pietermaritzburg region of Kwa-Zulu Natal and have been regularly associated with discharge of poor quality final effluent that did not subscribe to municipal regulation standards. Current treatment of choice for wastewater's in the edible oil industry have been limited primarily to dissolved air flotation combined with the use of chemical coagulants or physical separation of oil and grease via a gravity fat trap and subsequent pH correction. These physico-chemical methods have achieved limited success and the emulsified grease tends to clog sewer pipes and pumps producing poor quality effluents. Therefore, the aim of the current research was to develop suitable treatment technology focussing on adapting activated sludge process to remediate edible oil effluents and determine the microbial community of the process using novel molecular techniques.Item Investigation of combined effect of nitrogen, phosphorus and iron on lipid productivity of microalgae Ankistrodesmus falcatus KJ671624 using response surface methodology(Elsevier, 2015-02-15) Singh, Poonam; Guldhe, Abhishek; Kumari, Sheena K.; Rawat, Ismail; Bux, FaizalEnhancement of lipid accumulation is essential to improve the commercial feasibility of microalgal biodiesel production. An oleaginous microalgal strain, Ankistrodesmus falcatus KJ671624 was evaluated for its potential as a biodiesel feedstock in this study. The collective effect of nutrient (nitrogen, phospho-rous and iron) stresses on the lipid productivity of the selected strain was studied by response surface methodology. The highest lipid content of 59.6% and lipid productivity of 74.07 mg L−1 d−1 was obtained under nutrient stress with nitrogen 750 mg L−1, phosphorus 0 mg L−1 and iron 9 mg L−1. The photosyn-thetic behaviour validates the high lipid productivity under combined nutrient stress condition. Saturated fatty acid composition was increased by 38.49% under selected nutrient stress condition compared to BG11 medium. The enhanced lipid accumulation with suitable lipid profile (C16:0, C18:1, C18:2, C18:3) and biodiesel conversion of 91.54 ± 1.43% achieved in A. falcatus KJ671624 further confirm its potential as a promising feedstock for biodiesel production.Item Physico-chemical and biotic factors influencing microalgal seed culture propagation for inoculation of a large scale raceway pond(African Journals Online, 2014) Mutanda, Taurai; Ranjith Kumar, R.; Bux, FaizalThe growth of Chlorella vulgaris in open pond aquatic conditions poses serious challenges due to the interplay of both physico-chemical and biotic factors. We report here the monitoring of physico-chemical and biotic parameters affecting the propagation of C. vulgaris seed culture for inoculation of a large scale raceway pond (300 000 L capacity) in South Africa. The C. vulgarisstrain used for this purpose was isolated from a wastewater maturation pond and characterized for its potential for biomass and lipid production. The isolate was grown aseptically in 4 × 25 L aspirator bottles in BG-11 medium under ambient laboratory conditions and the culture was supplied with filtered air and exposed to 200 µmol photons per m2 per second using Gro-Lux agricultural fluorescent lights. The culture was transferred to a 500 L capacity portable pool under open conditions. This pond was used to further inoculate 3 more portable ponds. Physico-chemical and biotic growth parameters were monitored on a daily basis in the three ponds. The over reliance on fossil fuels will have a major impact on power supply in the near future if renewable sources of energy are not developed at a fast pace. The developed inoculum was subsequently used to inoculate an open raceway pond for large scale biomass production for biodiesel production.Item Artificial intelligence for the evaluation of operational parameters influencing Nitrification and Nitrifiers in an activated sludge process(Springer Science+Business Media, 2016) Awolusi, Oluyemi Olatunji; Nasr, Mahmoud; Kumari, Sheena K.; Bux, FaizalAbstract Nitrification at a full-scale activated sludge plant treating municipal wastewater was monitored over a period of 237 days. A combination of fluorescent in situ hybridiza-tion (FISH) and quantitative real-time polymerase chain reac-tion (qPCR) were used for identifying and quantifying the dominant nitrifiers in the plant. Adaptive neuro-fuzzy infer-ence system (ANFIS), Pearson’s correlation coefficient, and quadratic models were employed in evaluating the plant oper-ational conditions that influence the nitrification performance. The ammonia-oxidizing bacteria (AOB) abundance was with-in the range of 1.55 × 108–1.65 × 1010 copies L−1, while Nitrobacter spp. and Nitrospira spp. were 9.32 × 109–1.40 × 1011 copies L− 1 and 2.39 × 109 –3.76 × 1010 copies L−1, respectively. Specific nitrification rate (qN)was significantly affected by temperature (r 0.726, p 0.002), hy-draulic retention time (HRT) (r −0.651, p 0.009), and ammo-nia loading rate (ALR) (r 0.571, p 0.026). Additionally, AOB was considerably influenced by HRT (r −0.741, p 0.002) and temperature (r 0.517, p 0.048), while HRT negatively impact-ed Nitrospira spp. (r −0.627, p 0.012). A quadratic combina-tion of HRT and food-to-microorganism (F/M) ratio also im-pacted qN (r2 0.50), AOB (r2 0.61), and Nitrospira spp. (r2 0.72), while Nitrobacter spp. was considerably influenced by a polynomial function of F/M ratio and temperature (r2 0.49). The study demonstrated that ANFIS could be used as a tool to describe the factors influencing nitrification process at full-scale wastewater treatment plants.Item Physiological responses of carbon-sequestering microalgae to elevated carbon regimes(Taylor and Fancis Online, 2016) Bhola, Virthie Kemraj; Swalaha, Feroz Mahomed; Nasr, Mahmoud; Kumari, Sheena K.; Bux, FaizalIn order to identify a high carbon-sequestering microalgal strain, the physiological effect of different concentrations of carbon sources on microalgae growth was investigated. Five indigenous strains (I-1, I-2, I-3, I-4 and I-5) and a reference strain (I-0: Coccolithus pelagicus 913/3) were subjected to CO2 concentrations of 0.03–15% and NaHCO3 of 0.05–2 g CO2 l–1. The logistic model was applied for data fitting, as well as for estimation of the maximum growth rate (μmax) and the biomass carrying capacity (Bmax). Amongst the five indigenous strains, I-3 was similar to the reference strain with regards to biomass production values. The Bmax of I-3 significantly increased from 214 to 828 mg l–1 when CO2 concentration was increased from 0.03 to 15% (r = 0.955, P = 0.012). Additionally, the Bmax of I-3 increased with increasing NaHCO3 (r = 0.885, P = 0.046) and was recorded at 153 mg l–1 (at 0.05 g CO2 l–1) and 774 mg l–1 at (2 g CO2 l–1). Relative electron transport rate (rETR) and maximum quantum yield (Fv/Fm) were also applied to assess the impact of elevated carbon sources on the microalgal cells at the physiological level. Isolate I-3 displayed the highest rETR confirming its tolerance to higher quantities of carbon. Additionally, the decline in Fv/Fm with increasing carbon was similar for strains I-3 and the reference strain. Based on partial 28s ribosomal RNA gene sequencing, strain I-3 was homologous to the ribosomal genes of Chlorella sp.Item A low cost one pot synthesis of biodiesel from waste frying oil (WFO) using a novel material, b-potassium dizirconate (b-K2Zr2O5)(Elsevier, 2016) Singh, Veena; Bux, Faizal; Sharma, Yogesh ChandraBiodiesel was synthesized from waste frying oil (WFO) using b-potassium dizirconate (b-K2Zr2O5)asa novel heterogeneous catalyst. Synthesized catalyst was characterized by X-ray diffractometry (XRD), thermogravimetric analysis (TGA), attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR), particle size analyser, scanning electron microscopy (SEM), BET surface area and basicity. Various reaction conditions such as molar ratio of methanol: oil, catalyst amount (wt%), reaction temperature, time and reusability of catalyst were studied for transesterification reaction with the catalyst, b-K2Zr2O5. High biodiesel conversion of 96.85% was observed at a 10:1 M ratio (alcohol: oil), 4 wt% catalyst at 65 C for 2 h. WFO was characterized by GCMS and biodiesel conversion was ascertained by Fourier transform nuclear magnetic resonance (1H and 13C FTNMR) spectroscopy. It was first time that b-potassium dizirconate was used as a catalyst for biodiesel synthesis. The catalyst was reused up to five times without significant loss in its activity. Physical and chemical properties of FAME such as flash point, fire point, cloud point, density, and kinematic viscosity were deliberated.Item Trends and novel strategies for enhancing lipid accumulation and quality in microalgae(Elsevier, 2016) Singh, Poonam; Kumari, Sheena K.; Guldhe, Abhishek; Rawat, Ismail; Misra, Rohit; Bux, FaizalIn order to realize the potential of microalgal biodiesel there is a need for substantial impetus involving interventions to radically improve lipid yields upstream. Nutrient stress and alteration to cultivation conditions are commonly used lipid enhancement strategies in microalgae. The main bottleneck of applying conventional strategies is their scalability as some of these strategies incur additional cost and energy. Novel lipid enhancement strategies have emerged to research forefront to overcome these challenges. In this review, the latest trends in microalgal lipid enhancement strategies, possible solutions and future directions are critically discussed. Advanced strategies such as combined nutrient and culti-vation condition stress, microalgae–bacteria interactions, use of phytohormones EDTA and chemical additives, improving light conditions using LED, dyes and paints, and gene expression analysis are described. Molecular approaches such as metabolic and genetic engineering are emerging as the potential lipid enhancing strategies. Recent advancements in gene expression studies, genetic and metabolic engineering have shown promising results in enhancing lipid productivity in microalgae; however environmental risk and long term viability are still major challenges.Item Biodiesel synthesis from microalgae using immobilized Aspergillus niger whole cell lipase biocatalyst(Elsevier, 2016) Guldhe, Abhishek; Singh, Poonam; Kumari, Sheena K.; Rawat, Ismail; Permaul, Kugen; Bux, FaizalWhole cell lipase catalysis and microalgal feedstocks make overall biodiesel synthesis greener and sustainable. In this study, a novel approach of whole cell lipase-catalyzed conversion of Scenedesmus obliquus lipids was investigated for biodiesel synthesis. Microalgal biodiesel was characterized for its fuel properties. Optimization of process parameters for immobilized Aspergillus niger whole cell lipase-catalyzed biodiesel synthesis was carried out. Highest biodiesel conversion of 53.76% was achieved from S. obliquus lipids at 35 °C, methanol to oil ratio of 5:1 and 2.5% water content based on oil weight with 6 BSPs (Biomass support particles). Step-wise methanol addition was applied to account for methanol tolerance, which improved biodiesel conversion upto 80.97% and gave 90.82 ± 1.43% yield. Immobilized A. niger lipase can be used for 2 batches without significant loss in conversion efficiency. Most of the fuel properties of biodiesel met the specifications set by international standards.Item A logistic model for the remediation of filamentous bulking in a biological nutrient removal wastewater treatment plant(IWA Publishing, 2015-08) Deepnarain, Nashia; Kumari, Sheena K.; Swalaha, Feroz Mahomed; Ramjith, J.; Tandoi, V.; Pillay, K.; Bux, FaizalBiological nutrient removal (BNR) systems across the globe frequently experience bulking and foaming episodes, which present operational challenges such as poor sludge settling due to excessive filamentous bacteria. A full-scale BNR plant treating primarily domestic wastewater was monitored over a period of 1 year to investigate filamentous bacterial growth response under various plant operating parameters. Identification of filamentous bacteria by conventional microscopy and fluorescent in situ hybridisation indicated the dominance of Eikelboom Type021N, Thiothrix spp., Eikelboom Type 1851 and Eikelboom Type 0092. A cumulative logit model (CLM) was applied to elucidate significant relationships between the filamentous bacteria and plant operational parameters. The model could predict the potential abundance of dominant filamentous bacteria in relation to wastewater treatment plant operational parameters. Data obtained from the model corroborated with previous findings on the dominance of most filaments identified, except for Type 0092, which exhibited some unique traits. With further validation, the model could be successfully applied for identifying specific parameters which could contribute towards filamentous bulking, thus, providing a useful tool for regulating specific filamentous growth in full-scale wastewater treatment plants.Item Evaluation of anaerobic sludges as metal biosorbents and development of a biotechnological process for metal ion removal from selected wastewater(1997) Bux, Faizal; Kasan, Hamanth C.As a result of rapid expansion of the industrial sector and increasing population, the environment has been under phenomenal stress. The volume of sewage and other effluents has increased tremendously in the last century. Globally, approximately .12 million tonnes of dry sludge biomass is produced and discarded of by landspreading, landfilling, incineration or dumping in lagoons and oceans. The discharge of industrial effluents into receiving waters has been documented to be the cause of severe environmental contamination. Heavy metals have been the cause of particular environmental concern. Their toxic and carcinogenic potentials at low concentrations, as well as the large quantities disposed to the environment, have prioritised them as leading contaminants. Current technologies of remediating heavy metal containing effluents are expensive and, in most cases, ineffective. Locally, most industries are merely diluting their effluents, thus resulting in the loss of valuable water resources. Waste sludges have shown the ability to adsorb heavy metals from their aqueous environment. Therefore, the current study attempted firstly, to compare biosorptive capacities of various waste sludges for a range of heavy metal ions, and secondly, to establish a relationship, if any, between biosorptive capacity and sludge surface charge. Finally, a laboratory scale biosorption process, encompassing desorption and recovery of metal ions from sludge surfaces, would have to be developed. Effluents used included pure, metal solutions of divalent zinc, cadmium, copper, nickel, trivalent and hexavalent chromium. In addition, synthetic effluents comprising a cocktail of the above-mentioned metal ions as well as an industrial effluent from a metal plating company were used. Five waste digested sludges were prepared and challenged against pure metal solutions to determine and compare their respective biosorptive capacities. Mechanisms of biosorption were elucidated using the Langmuir adsorption isotherm model. Sludge surface charge was determined using the millivolt quantification method. Upscaling of bioreactor trials to fully mixed laboratory scale was also investigated. These experiments encompassed the use of three sludges showing the greatest potential for biosorption and desorption using the selected mineral acid, H2S04, In addition, a simultaneous fully mixed biosorption and desorption process was designed and optimised. Subsequent trials involved comparing the latter process with a packed bed configuration whereby biomass was immobilised using poly sulfone resin. The overall comparative adsorptive capacities of the sludges (SI-SS) for metal ions in single solutions was S3 > S2 > S4 > SS > SI. Surface charge determination showed S3 to contain the most electronegative charge, with other sludges following in the same descending order as mentioned above. These findings supported the theory of a direct correlation between sludge surface charge and biosorptive potential. The affinity series of the sludges for metal ions followed the descending order of Cd2+ > Cu2+ > Ni2+ > Zn2+ > Cr6+ > Cr3+. Fully mixed studies, using mixed synthetic effluents, resulted in lower biosorptive capacities being recorded by the three selected sludges ie., S2, S3 and S4, as compared to single solution experiments. Biosorption studies with industrial effluent, containing Zn2+ as the most prevalent metal at 119.4 mg.F'. resulted in S3 biosorbing a maximum of 4.5 mg.g' of the cation. Sulphuric acid (H2S04) at O.2N, hydrochloric acid (HCI) at O.2N and acetic acid (CH3COOH) at O.4N were tested for their desorptive efficiencies. Sulphuric acid proved to be the most effective desorbing agent. Using S3 as biosorbent and O.2N H2S04 as desorbent, the manipulation and operation of a simultaneous process proved to be successful since both biosorption and desorption occurred concurrently, thus reducing time required for successful remediation considerably. Immobilised biomass, in a packed bed configuration, produced acceptable final effluent regarding standards as stipulated by the Durban Municipality for trade effluents. However, biosorption capacity of the sludge was compromised, with subsequent reductions in desorption being recorded, when the process was compared to fully mixed trials. Affinity series determined for the packed bed process wasC~+ >Cd2+>Zn2+>Cu2+>Cr6+ >Ni2+. Waste digested sludge has shown potential as metal biosorbent on an industrial scale. The present findings have succeeded in demonstrating a novel laboratory scale biotechnological process for the remediation of metal laden industrial effluents.