Faculty of Applied Sciences
Permanent URI for this communityhttp://ir-dev.dut.ac.za/handle/10321/5
Browse
8 results
Search Results
Item Optimization of biomass and lipids production from microalgae using wastewater in a pilot scale raceway pond(2021) Rawat, Ismail; Bux, FaizalMicroalgae provide a sustainable renewable solution for the production of commodity products such as liquid biofuels. There are numerous benefits to using algae for the production of biofuels, however, the cost of production is a major hurdle to commercial-scale development. Major factors influencing the production of algae are the cost of nutrients, availability of water, contamination, and grazers. Research into algal biomass for biofuels production at laboratory scale does not translate directly to cultivation at large scale due to the change in cultivation conditions and the constant flux of environmental factors. This study focuses on the upstream processes of cultivation of biomass in a ~ 1146 m2 raceway pond. It demonstrates biomass productivity under different climatic conditions and utilisation of post-chlorinated wastewater as a water and nutrient source. The study further elucidates the population dynamics of the system and provides insight into the challenges faced during the cultivation of algae at large scale. An indigenous Scenedesmus sp. gave biomass productivity of 31.23 g/m2 /d with lipid production of 29.6 % lipid/g DCW in a 10 m2 raceway pond in a greenhouse using BG11. Biomass productivity was reduced to 13.09 g/m2 /d with a lipid content of 22.9 % lipid/g DCW under 3-fold higher irradiance. Biomass productivity of circular 3000L ponds at the large scale site resulted in the highest biomass and acceptable lipid content using 250mg/L NaNO3 although significantly lower than the 10 m2 raceway ponds. Wastewater has shown potential to replace conventional media. Post-chlorinated wastewater was found to have low levels of nitrogen and phosphorus but contained metals that act as micronutrients for algae. Supplemented wastewater proved to be an effective growth. Six individual runs of a covered 1146 m2 raceway pond driven by paddlewheel were conducted over 15 months. The average water temperature ranged from 20.61±0.68°C during mid-winter to 31.03±2.22°C in late summer. Daylight ranges from 10.25 to 14 hours in winter and summer respectively. The highest average light intensity was 359.00±212.71 µmol/m2 /s from Mid-winter to early spring and 645.44±330.58 µmol/m2 /s in late summer. Biomass productivities were low ranging from 2.7 to 7.34 g/m2 /d for most runs of the raceway pond, mainly due to the long periods of cultivation. Average productivity at day 7 for all raceway runs was 7.25 g/m2 /d. Adaptive Neuro-Fuzzy Inference System (ANFIS) modelling of the system elicited that the major factors affecting biomass productivity in the raceway pond were light intensity, pH, and depth for the raceway pond. The model showed that maximum biomass productivity is possible at a depth between 20 and 22 cm at light intensities between 200 and 400 µmol/m2 /s. pH in the range of 9 to 9.5 correlated positively with light intensity ranging from 200 to 1000 µmol/m2 /s with maximum biomass expected in the region of 400 to 500 µmol/m2 /s. The main algal constituents for the raceway ponds were Scenedesmus obliquus, Scenedesmus dimorphus, Chlorella, Keratococcus, and species of unidentified cyanobacteria. Either Scenedesmus or Chlorella was dominant for extended periods. Bacteria in open systems can have a positive or negative effect on the growth of microalgae but is dependent on the strains of microalgae and bacteria as well as prevailing conditions making these systems highly complex. Rhodobacteraceae, Plactomycetaceae, Xanthomonadaceae, Flavobacteriaceae, Phycisphaeraceae, Comamonadaceae, and Cyclobacteriaceae were found to be the major families of bacteria that proliferate at different levels during the cultivation period in the circular ponds and the raceway pond. These families of bacteria have several beneficial traits to algae cultivation however further investigation is required. Modelling the system revealed that pH, depth, and light intensity were factors having a substantial effect on biomass productivity. As the system was carbon limited addition of CO2 (preferably a waste stream) could significantly enhance the overall biomass productivity. A major factor negatively affecting biomass productivity was the size of the pond. Inadequate mixing impacts biomass productivity in terms of access to nutrients and gaseous exchange. Shorter periods of cultivation resulted in higher productivities. For the scale of the system, semi-continuous harvesting would be required to achieve shorter residence time. This must be balanced against the energy utilization and cost of harvesting potentially lower culture densitiesItem Investigation of combined effect of nitrogen, phosphorus and iron on lipid productivity of microalgae Ankistrodesmus falcatus KJ671624 using response surface methodology(Elsevier, 2015-02-15) Singh, Poonam; Guldhe, Abhishek; Kumari, Sheena K.; Rawat, Ismail; Bux, FaizalEnhancement of lipid accumulation is essential to improve the commercial feasibility of microalgal biodiesel production. An oleaginous microalgal strain, Ankistrodesmus falcatus KJ671624 was evaluated for its potential as a biodiesel feedstock in this study. The collective effect of nutrient (nitrogen, phospho-rous and iron) stresses on the lipid productivity of the selected strain was studied by response surface methodology. The highest lipid content of 59.6% and lipid productivity of 74.07 mg L−1 d−1 was obtained under nutrient stress with nitrogen 750 mg L−1, phosphorus 0 mg L−1 and iron 9 mg L−1. The photosyn-thetic behaviour validates the high lipid productivity under combined nutrient stress condition. Saturated fatty acid composition was increased by 38.49% under selected nutrient stress condition compared to BG11 medium. The enhanced lipid accumulation with suitable lipid profile (C16:0, C18:1, C18:2, C18:3) and biodiesel conversion of 91.54 ± 1.43% achieved in A. falcatus KJ671624 further confirm its potential as a promising feedstock for biodiesel production.Item Trends and novel strategies for enhancing lipid accumulation and quality in microalgae(Elsevier, 2016) Singh, Poonam; Kumari, Sheena K.; Guldhe, Abhishek; Rawat, Ismail; Misra, Rohit; Bux, FaizalIn order to realize the potential of microalgal biodiesel there is a need for substantial impetus involving interventions to radically improve lipid yields upstream. Nutrient stress and alteration to cultivation conditions are commonly used lipid enhancement strategies in microalgae. The main bottleneck of applying conventional strategies is their scalability as some of these strategies incur additional cost and energy. Novel lipid enhancement strategies have emerged to research forefront to overcome these challenges. In this review, the latest trends in microalgal lipid enhancement strategies, possible solutions and future directions are critically discussed. Advanced strategies such as combined nutrient and culti-vation condition stress, microalgae–bacteria interactions, use of phytohormones EDTA and chemical additives, improving light conditions using LED, dyes and paints, and gene expression analysis are described. Molecular approaches such as metabolic and genetic engineering are emerging as the potential lipid enhancing strategies. Recent advancements in gene expression studies, genetic and metabolic engineering have shown promising results in enhancing lipid productivity in microalgae; however environmental risk and long term viability are still major challenges.Item Biodiesel synthesis from microalgae using immobilized Aspergillus niger whole cell lipase biocatalyst(Elsevier, 2016) Guldhe, Abhishek; Singh, Poonam; Kumari, Sheena K.; Rawat, Ismail; Permaul, Kugen; Bux, FaizalWhole cell lipase catalysis and microalgal feedstocks make overall biodiesel synthesis greener and sustainable. In this study, a novel approach of whole cell lipase-catalyzed conversion of Scenedesmus obliquus lipids was investigated for biodiesel synthesis. Microalgal biodiesel was characterized for its fuel properties. Optimization of process parameters for immobilized Aspergillus niger whole cell lipase-catalyzed biodiesel synthesis was carried out. Highest biodiesel conversion of 53.76% was achieved from S. obliquus lipids at 35 °C, methanol to oil ratio of 5:1 and 2.5% water content based on oil weight with 6 BSPs (Biomass support particles). Step-wise methanol addition was applied to account for methanol tolerance, which improved biodiesel conversion upto 80.97% and gave 90.82 ± 1.43% yield. Immobilized A. niger lipase can be used for 2 batches without significant loss in conversion efficiency. Most of the fuel properties of biodiesel met the specifications set by international standards.Item Biocatalytic conversion of lipids from microalgae Scenedesmus obliquus to biodiesel using Pseudomonas fluorescens lipase(Elsevier, 2015-01-31) Guldhe, Abhishek; Singh, Bhaskar; Rawat, Ismail; Perumal, Kugen; Bux, FaizalConversion of microalgal lipids using biocatalyst is a novel and greener approach to produce biodiesel. Free and immobilized lipases from Candida sp. and Pseudomonas fluorescens along with free lipases from porcine pancreas and wheat germ were screened for biodiesel conversion of Scenedesmus obliquus lipids. Among selected lipases from various sources immobilized lipase from P. fluorescens showed superior biodiesel conversion. Optimization of reaction parameters viz. lipase amount, temperature, methanol to oil molar ratio and water content was carried out using response surface methodology. Best conversion of 66.55% was achieved at 35 °C, methanol to oil ratio of 3:1 with 10% enzyme amount and 2.5% water content based on oil weight. To tackle methanol tolerance step-wise methanol addition was applied, which improved biodiesel conversion upto 90.81%. Immobilized P. fluorescens lipase can be used for 4 batches without much loss in conversion efficiency (>95%). Biodiesel produced has the cetane number of 51.77, Calorific value of 37.67 MJ kg−1. Most of the fuel properties of biodiesel met the specifications set by ASTM and EN standards.Item Biodiesel from microalgae: A critical evaluation from laboratory to large scale production(Elsevier, 2013) Rawat, Ismail; Ranjith Kumar, R.; Mutanda, Taurai; Bux, FaizalThe economically significant production of carbon-neutral biodiesel from microalgae has been hailed as the ultimate alternative to depleting resources of petro-diesel due to its high cellular concentration of lip-ids, resources and economic sustainability and overall potential advantages over other sources of biofu-els. Pertinent questions however need to be answered on the commercial viability of large scale production of biodiesel from microalgae. Vital steps need to be critically analysed at each stage. Isolation of microalgae should be based on the question of whether marine or freshwater microalgae, cultures from collections or indigenous wild types are best suited for large scale production. Furthermore, the determination of initial sampling points play a pivotal role in the determination of strain selection as well as strain viability. The screening process should identify, purify and select lipid producing strains. Are natural strains or stressed strains higher in lipid productivity? The synergistic interactions that occur nat-urally between algae and other microorganisms cannot be ignored. A lot of literature is available on the downstream processing of microalgae but a few reports are available on the upstream processing of mic-roalgae for biomass and lipid production for biodiesel production. We present in this review an empirical and critical analysis on the potential of translating research findings from laboratory scale trials to full scale application. The move from laboratory to large scale microalgal cultivation requires careful plan-ning. It is imperative to do extensive pre-pilot demonstration trials and formulate a suitable trajectory for possible data extrapolation for large scale experimental designs. The pros and cons of the two widely used methods for growing microalgae by photobioreactors or open raceway ponds are discussed in detail. In addition, current methods for biomass harvesting and lipid extraction are critically evaluated. This would be novel approach to economical biodiesel production from microalgae in the near future. Glob-ally, microalgae are largest biomass producers having higher neutral lipid content outcompeting terres-trial plants for biofuel production. However, the viscosities of microalgal oils are usually higher than that of petroleum diesel.Item Improving the feasibility of producing biofuels from microalgae using wastewater(Taylor and Francis, 2013-10-08) Rawat, Ismail; Bhola, Virthie; Ranjith Kumar, R.Biofuels have received much attention recently owing to energy consumption and environmental concerns. Despite many of the technologies being technically feasible, the processes are often too costly to be commercially viable. The major stumbling block to full-scale production of algal biofuels is the cost of upstream and downstream processes and environmental impacts such as water footprint and indirect greenhouse gas emissions from chemical nutrient production. The technoeconomics of biofuels production from microalgae is currently unfeasible due to the cost of inputs and productivities achieved. The use of a biorefinery approach sees the production costs reduced greatly due to utilization of waste streams for cultivation and the generation of several potential energy sources and value-added products while offering environmental protection. The use of wastewater as a production media, coupled with CO2 sequestration from flue gas greatly reduces the microalgal cultivation costs. Conversion of residual biomass and by-products, such as glycerol, for fuel production using an integrated approach potentially holds the key to near future commercial implementation of biofuels production.Item Screening for indigenous algae and optimisation of algal lipid yields for biodiesel production(2011) Rawat, Ismail; Bux, FaizalThe depletion of global energy supplies coupled with an ever increasing need for energy and the effects of global warming have warranted the search for alternate renewable sources of fuel such as biodiesel. First generation biofuels are not sustainable enough to meet long term global energy requirements and more recently there has been concern expressed as to the potential negative implication of crop based biofuels in the form of negative energy balances and potentially no greenhouse gas benefit due to land utilisation not being taken into account. Microalgae have shown great promise as a sustainable alternative to first generation biofuels. They have faster growth rates, have greater photosynthetic efficiencies, require minimal nutrients and are capable of growth in saline waters which are unsuitable for agriculture. Microalgae utilise a large fraction of solar energy and have the potential to produce 45 to 220 times higher amounts of triglycerides than terrestrial plants. The use of microalgae for biodiesel production requires strain selection, optimisation and viability testing to ascertain the most appropriate organism for large scale cultivation. This study focuses on bioprospecting for indigenous lipid producing microalgae, screening, selection and optimisation of growth and lipid yields with respect to nutrient limitation. Further we have ascertained the sustainability of a selected species of microalgae in open pond system. Chlorella sp. and Scenedesmus sp. were found to be dominant amongst the isolates. Strains we selected and underwent media selection and growth and lipid optimisation trials. BG11 media was selected as the most appropriate media for the growth of the selected Chlorella and Scenedesmus strains. Little variation in growth was observed for both cultures ten days into cultivation under varying nitrate concentrations. Phosphate optimum was shown to be 0.032g/l for Scenedesmus sp and 0.04g/l for Chlorella sp. Best lipid yield determined during exponential growth was achieved in cultures with 0.3g/L to 0.6g/L nitrate and phosphate as per BG11 medium. pH optimisation showed that cultures may be adapted to growth at higher pH over time. The optimum pH range for growth was determined to be narrow and was found to be between pH 10 and pH 11. Chlorella sp. was shown to be sustainable as a dominant culture in open pond system. Open pond systems however are prone to contamination by other species of microalgae within weeks of inoculation.